1、  大樓建筑物樓板打混凝土之前，自來水管線須依規定做水壓實驗，實驗壓力一般為10KG/平方厘米或最高使用壓力1.5倍，并應保持1小時如無漏水可打混凝土，上述水壓試驗，一般均每層分別進行。

2、  活套管試水壓時，管線須予蓋上，如環境許可時，可僅留活套頭部分不蓋土，試水前須蓋土的目的，主要為防止活套水試水壓時之脫開，如在市區因交通流量大。一般可全部蓋土后試水壓。

3、  管線施工后須分段試水壓，每段長度約500-1000M，試靜水壓力為10KG/平方厘米或者最高使用壓力1.5倍，并應保持1小時并勘察是否有漏稅現象，試壓的管線較高之位置與管端，應裝設排氣閥。

4、  管線埋設須先填砂，厚度最小10CM，管子不得與石頭直接接觸。

5、  大樓樓板的電子配管以直線配管為原則，如需要彎曲時，一個彎曲角度應在90度以內，且一區間（兩接線盒間）的管線彎曲角度，合計不得超過270度，且配線長度不得超過30M。

6、  電器用管與接線盒。裝配后于打混凝土?xí)r應防止受到破壞或損傷，如有破損應即修復，以免影響往后的拉線工作。

7、  樓板內的埋設配管，一個交叉點的管子，應為2支以下，不得同一位置有3支管子相交叉。

8、  樓板打混凝作業中，水電工人員應常駐于工地，以便處理配管上的突發時間。

9、  給水管用膠合劑不得含有毒和利于微生物生長物質，不得對飲用水水質有影響。

10、寒帶地區，外露管道施工，需作防凍設施。

11、以上注意事項僅供參考，實際施工時請遵守中國工程建設標準化協會標準的相關的規定。

Notice ltems of PVC Piping installation:

1 Before comcreting the floor, run water pressure test on the tape water pipe line with testing water pressure retained for one hour at 10KG/CM2, nor higher than 1.5 times of the working pressure. Start concreting only when no leakages is abserved. Usually, this test is separately run by floor.

2 Earth coverage over the pipe line is required on testing the water pressure of spigot pipe, which however may be left bare only the connecting parts if working environment permits. The purpost of earth coverage is required before the test to be run un where heavy,traffice flow occura,such as in the downtown area.

3 Run the water pressure test by section for approaxi mately  very 500-1000M on pipe completed, at the testing bydrostatic pressure retained for one hour at not lower that 10KG//CM2, nor higher than 1.5times of the working pressure. Pbserve for any leakage.. Provide vent walve to the pipe line at the pipe end or at where with higher elevatiaon..

4 Sand filling with layer thickness not less than 10 cm is required before the embedment of pipe line. DO ot cause the pipe to contact directly with any stone.

5 lLinear allocation governs the pipe for electric con duit on the builking floor. If bending is required,the bend angle shall not be larger than 90, and not larger than 270 in total in one area The wiring length shall not be larger than 30M.

6 Prevent the assembled pipe for electric conduit use and wiring cases from being destructed or damaged by or more pipes at the same intersection is not allowed.

7 Number for pipe at intersection embedded in the floor shall not be larger than two as illustrated below. Three or more pipes at the same intersection is not allowed.

8 Civil utilities technician shall be always available on site during the operation of concreting in case of any incident to the piping work.

9 The adhesives for PVC pipesin water works which can not include any toxins or sonmethis that was complied with microbeds to grow.and shouldn`tinfluenced with potable water.